Unknown 23 de septiembre de , Unknown 27 de octubre de , Unknown 13 de noviembre de , Unknown 13 de diciembre de , Walterr 28 de febrero de , Unknown 25 de marzo de , Unknown 23 de junio de , Cristopher Ortiz 20 de marzo de , Unknown 2 de abril de , Unknown 21 de junio de , Sony 20 de marzo de , Cesar 10 de abril de , Unknown 27 de abril de , Unknown 18 de abril de , Unknown 27 de mayo de , Unknown 17 de junio de , Unknown 27 de julio de , Unknown 2 de agosto de , Unknown 14 de octubre de , Tavo 17 de octubre de , Crisstian 19 de noviembre de , Unknown 24 de noviembre de , Unknown 17 de enero de , Unknown 1 de febrero de , Yaz 3 de febrero de , Unknown 21 de abril de , Unknown 27 de marzo de , Unknown 12 de abril de , Unknown 19 de mayo de , Unknown 23 de mayo de , Unknown 11 de junio de , Unknown 12 de junio de , Unknown 6 de julio de , Unknown 28 de septiembre de , Unknown 29 de agosto de , Unknown 26 de septiembre de , Unknown 20 de octubre de , Unknown 19 de noviembre de , Unknown 20 de noviembre de , Unknown 6 de diciembre de , Unknown 2 de febrero de , Unknown 29 de diciembre de , Unknown 16 de enero de , Unknown 20 de enero de , Unknown 29 de enero de , Unknown 24 de febrero de , Marcar por contenido inapropiado.
Descargar ahora. Carrusel anterior Carrusel siguiente. Buscar dentro del documento. Condiciones Permanente 2. La charola 1 esta del lado del BU Fig.
Retiro de bandas y tornillos. Ensamble de la tarjeta SW 6. El kit de cushion consiste en Fig. Anexo 1. Anonymous 0mgOZ8ikOi. Eduardo Echeverry. Jorge Corrales. Javier Rodriguez Quintero. Josp Art. Francisco Mora. Ing Pett Aparicio. Gabriela Prada. Gilbert Benavides. Pepe Ollober. Ricardo Cabral. David Ocampo Gonzalez. F : Stop by the problem other than mechanical problem while chucking down.
This mode enables CD to repeat playback for limitless times. To release from this mode, operate the cold reset. Use this mode when returning the set to the customer after repair.
Press [x] button, [DISC 1] button and [? The system turns off automatically. This mode let you lock the disc tray. This mode is used to check the meter device. When you want to perform count total step from Initial Switch to Max Switch operation mode, press [M] button.
The meter pointer will move from Initial Switch to Max Switch and finally move back to the middle position. The total step count information appears on the fluorescent indicator tube. When you want to perform count total step from Max Switch to Initial Switch operation mode, press [m] button. The meter pointer will move from Max Switch to Initial Switch and finally move back to the middle position.
To release from this mode, do the step 2 again. Do not bring the head magnetizer close to the erase head. Do not use a magnetized screwdriver for the adjustments. After the adjustments, appiy suitable locking compound to the parts adjusted. The adjustments should be performed with the rated power supply voltage unless otherwise noted. Meter Reading 2. Mode: Playback test tape PA 6. Turn the adjustment screw and check output peaks. Note: 1. CD Block is basically designed to operate without adjustment.
Therefore, check each item in order given. Clean the object lens by an applicator with neutral detergent when the signal level is low than specified value with the following checks. Procedure : 1. Turn the power ON. Load a disc YEDS and actuate the focus search. In consequence of open and close the disc tray, actuate the focus search 4. Confirm that the oscilloscope waveform S-curve is symmetrical between A and B. And confirm peak to peak level within 1. S-curve waveform symmetry. Load a disc YEDS and playback.
Confirm that oscilloscope waveform is clear and check if RF signal level is correct or not. Turn on the set. Input the following signal from signal generator to FM antenna input directly. You cannot use video cable for checking. Use signal generator whose output impedance is 75 ohm.
R-ch is omitted due to same as L-ch. In addition to this, the necessary note is printed in each block. For Printed Wiring Boards. Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Voltage variations may be noted due to normal production tolerances.
R 4. Some delay should be anticipated when ordering these items.
0コメント